Product ID:AB 2143 PART B
MSDS Date:01/01/1987
FSC:8040
NIIN:00N015099
Kit Part:Y
MSDS Number: BKPTF

DEXTER CORPORATION HYSOL DIV

2850 WILLOW PASS ROAD
PITTSBURG, CA 94565
US

Emergency Phone: 415-687-4201

Info Phone: 415-687-4201

Cage: 79436

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

DIETHYLENE TRIAMINE

CAS: 111-40-0

RTECS: IE1225000

Fraction By Weight: 12%

OSHA PEL 1 PPM

ACGIH TLV: S, 1 PPM; 9192

POLYAMIDE RESIN

Fraction By Weight: 75%

ASBESTOS, CHRYSOTILE

CAS: 12001-29-5

RTECS: CI6478500

Fraction By Weight: 13%

OSHA PEL 0.2 FIBERS/CC

ACGIH TLV: 2 FIBERS/CC; A1;9192

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:YES
Health Hazards Acute and Chronic:CORROSIVE TO SKIN AND EYES. CAN CAUSE
CHEMICAL BURNS TO SKIN AND SEVERE CHEMICAL BURNS TO EYES. VAPORS
IRRITATING AND MAY CAUSE CHEST DISCOMFORT AND BRONCHITIS SYMPTOMS.
MODERATELY TOXIC BY INGESTION. USERS SHOULD CONSULT CURRENT
PERMISSIBLE LEVELS OF EXPOSURE FOR ASBESTOS .
Explanation of Carcinogenicity:ASBESTOS: IARC-GROUP 1; NTP-GROUP 1;
ACGIH-GROUP 1.
Effects of Overexposure:NONE SPECIFIED BY MANUFACTURER.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:GIVE WATER OR MILK IF SWALLOWED, DO NOT INDUCE VOMITING. GET
MEDICAL HELP. SKIN: FLUSH WITH WATER. THEN WASH THOROUGHLY WITH
SOAP AND WATER. EYE: FLUSH WITH WATER IMMEDIATELY FOR AT LEAST 15
MINUTES A ND GET MEDICAL HELP. INHAL: REMOVE TO FRESH AIR. SUPPORT
BREATHING (GIVE 0*2/ARTF RESP) .

Flash Point Method:COC
Flash Point:215F,102C
Extinguishing Media:FOAM, CO*2, DRY CHEMICAL, WATER SPRAY.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT WHEN FIGHTING FIRES IN CONFINED AREAS.
Unusual Fire/Explosion Hazard:DENSE SMOKE MAY BE LIBERATED.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES AND CHEMICAL
WORKERS GOGGLES. COVER WITH ABSORBENT MATERIAL, THEN SCRAPE UP AND
TRANSFER TO METAL CONTAINER. WIPE UP REMAINING RESIDUE WITH
SOLVENTS, OBSERVING SOLVENT FLAMMABILITY CAUTIONS, OR USE
DETERGENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP PRODUCT COOL IN ACCORDANCE WITH
LABEL INSTRUCTIONS.
Other Precautions:FOLLOW RECOMMENDED CURING SCHEDULE. IF IT IS
NECESSARY TO SAND THE CURED ADHESIVE "WET SANDING" IT IS
RECOMMENDED THAT ONE SHOULD ELIMINATE ALL AIRBORNE ASBESTOS.

Respiratory Protection:THE USE OF A NIOSH/MSHA APPROVED MASK FOR TOXIC
DUSTS IS REQUIRED IF CURED PRODUCT IS TO BE DRY SANDED, ABRADED,
ETC.
Ventilation:MECHANICAL (GENERAL)/LOCAL EXHAUST RECOMMENDED WHEN SANDING
CURED PRODUCT.
Protective Gloves:IMPERVIOUS PLASTIC OR RUBBER.
Eye Protection:CHEMICAL WORKERS GOGGLES.(SEE SUPP DATA)
Other Protective Equipment:AS NEEDED TO PROTECT SKIN AND CLOTHING.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
CNDTNS (POLYM): CURING SURFACES TO BE BONDED. FAILURE TO OBSERVE
CAUTIONS MAY RESULT IN EXCESSIVE HEAT BUILD UP WITH THE RELEASE OF
TOXIC GASES. EYE PROT: MAY ADD FULL LENGTH FACE SHIELD TO GOGGLES
(F P N).

HCC:T6
Boiling Pt:B.P. Text:>400F,>204C
Spec Gravity:0.936
Solubility in Water:SLIGHT
Appearance and Odor:GREEN PASTE
Percent Volatiles by Volume:< 1

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CO, NO*X, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:AVOID MIXING RESIN & CURING AGENT IN
BATCHES GREATER THAN ONE POUND TOTAL & DO NOT HEAT MATERIAL UNLESS
(SEE SUPP DATA)

Waste Disposal Methods:DISPOSE OF AS HAZ WASTE ACCORDING TO DOT HAZ
CLASS. IF NOT REGULATED BY DOT DISPOSE OF AS ORM-E. DISP METH CAN
BE LAND BURIAL OR CHEM INCINERATION AS REGULATED BY ALL
GOVERNMENTAL AGENCIES. DISPOSAL M UST BE I/A/W FEDERAL, STATE &
LOCAL REGS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.